Logo

P3471 Engine Trouble Code

P3471 Engine

When you check engine light came on code P3471 the reason should be . However your vehicle's manufacturer may have a different definition for the P3471 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

When your car's 'P3471 Check Engine' light comes on, it's usually accompanied by a sinking feeling in the pit of your stomach. The light could mean a costly problem, like a bad catalytic converter, or it could be something minor, like a loose gas cap. But in many cases, it means at minimum that you'll be visiting the car dealer to locate the malfunction and get the engine conducted light turned off.

P3471 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
3
Ignition System Or Misfire
4
Fuel Temperature Sensor B Circuit Range/Performance
7
Injection lump Fuel Metering Control 'B' High (Cam/Rotor/Injector)
1
Glow Plug/Heater Circuit 'A' Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P3471 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P3471 engine trouble code is about Glow Plug/Heater Circuit 'A' Malfunction. Fuel Temperature Sensor B Circuit Range/Performance and Injection lump Fuel Metering Control 'B' High (Cam/Rotor/Injector) causes most of code P3471.

Reason For P3471 Code

The reason of P3471 OBD-II Engine Trouble Code is Fuel Temperature Sensor B Circuit Range/Performance.

P3471 code on vehicles with electronically controlled automatic transmissions, the 3-4 shift solenoid is responsible for actuating the hydraulic circuits to activate clutches or bands that change gears inside the automatic transmission in your car.

How To Repair P3471 Code

Before starting let's see P3471 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P3471 code stored in the ECU.
  • Technicians will note P3471 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

The fluid pressure sensor provides the PCM with the data necessary to monitor the transmission performance. If the fluid pressure increases, the electrical voltage reading from the pressure sensor will increase; if the pressure decreases, the voltage decreases.

This can result in damage to engine parts over duration of time. We consider that you seal the engine leaks right away if possible. Rising fuel usage can often be associated to a defect in how your engine generates fuel. When matched up with a check engine light in sight and other engine-associated symptoms, the issue can be even more critical. If you see that your vehicle is consuming more fuel, have it inspected and repaired by a mechanic.

Sometimes P3471 code comes with P347100 code.

Diagnosis Of Engine Error OBD Code P3471

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P3471 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P3471 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.